Thursday, 2 May 2013

[RWBY] Crescent Rose "The High Velocity Sniper Scythe"

After being shown the first RWBY trailer earlier back in 2012, I have just been transfixed with the art style and creative direction, the new IP being produced by Roosterteeth seems to be headed. One of the many things that’s got me invested are the crazy weapon designs, and after seeing Crescent Rose in action, I was asked by a close friend to help make to make one.


 So to start off with I bought a heavy duty outdoor garden broom, which will act as the base frame and support skeleton of the entirte scythe.

 

What’s particularly great about using this particular model of broom is that it comes premade with a screw detectable head, meaning I’ll be able to detach the scythe head and the handle later down the line making transportation much easier.


Separating the broom head from the handle, I started to trim down the bristles with some scisccors.

  
 

Then yanked them out with a pair of pliers with relative ease.

 

Afterwhich I then sawed, sanded and grinded away all the unwanted parts of the broom head until only the vital screw thread nub remained.


With the plastic nub shaped which will act as the focal point of the entire scythe head; I needed to build the gunbarrel of the scythe that would go around it, this was done mainly with PVC sheeting (Sintra) I had lying around, which I cut out and assembled togther with hotglue.


In regards to cutting out the holes to make the clearance fit to accommodate the nub, I found that wood carving tools were very useful to start off with, then cleaning up the edges with a hand file. 


For the muzzle that slots down the top, that was done with a hacksawed piece of PVC piping which then had thin rectangular strips hot glued along the inside to simulate gun barrel splines.


Putting the walls on the lower and upper half of the gun barrel everything was assembled on top of and glued around the plastic nub.

 

With that out of the way, I then proceeded to work on the back half of the scythe head, which involved layering PVC sheets together

 

Getting the crux of this build; whenever I've made props in the past that have had open cavities I always found that they prop will experience some degree of bending and  flimsiness just from general use. Though very lightweight they are very prone to breaking should they be hit against something or be used for anything other than photography.

A way I am starting to become a fan of to overcome this is taken from IKEA furniture design philosophy, which is to hot glue cardboard fins across the span of these cavities such that they can also be sealed up later and hidden from view.


Trust me there will be an immediate and noticeable improvement in strength just by putting in a sufficient number of fins which will drastically prolong the life and functionality of a prop and still keep the weight down.


For the front business end of Crescent Rose, again this involved laminating sheets of PVC sheets onto one another but also using wonderflex to do the various raised details.
 

 I should note Wonderflex has two sides to it, a smooth side and a woven fibered side so when cutting out your transferred templates make sure you mirror the pieces to match the side you want to be facing out...trust me it'll save you the frustration and wasted material


To glue all the parts together I've use mainly epoxy glue, which comes in a tiny tube that has two nozzles on it , simply mix the two solutions and smear on with a popsicle stick, the glue cures in 5 minutes for a very strong bond.


  The dome parts on either side were made from a cheap LED light fixtures that I trimmed down.


Moving onto the actual blade, using the PVC base I cut out, the bevel of the blade was shaped with automotive body filler (bondo) and then sanded down.


For the top fin of the scythe I glued a bridging base across the span of the scythe which it would sit upon, and again used this opportunity to put in as many of those cardboards fins inside as I could.

Gluing the blade part to the rest of the scythe head with Araldite Super Strength epoxy, I topped it off with a couple coats of primer.



Starting work on the scythe handle; using the original garden broom handle, I used contact cement to glue on the two faces of what would eventually become the handle base structure.


 And since the handle is expected to experience the most handling and wear, I had to incorporate a whole heap of fins to ensure that there is as minimal bending or warping as possible. So fins, fins, fins, time consuming but essential.



Closing up the exposed faces with PVC pannels and using wonderflex to the various details that runs along the handle its starting to take shape.


With the front half looking good I underwent a similar build process to do the back half.

 

In particular  the spear tip on the end of the handle was cut out of MDF.


The blades shaped with a belt sander making sure not to over cut the bevel.


and finishing off with piece of PVC.


The side bolt handle was made from a cheap hand fan I found one day, which happen to have the right shape and length.


Gluing on all the remaing details like the trigger and such with tubes of epoxy glue, giving it all a good coat of primer i was ready to begin painting.


The paint job was done mainly with acrylic paints and a sharpie to do the edges to help bring out the crisp aesthetic of the scythe; the emblem on the magazine was drawn using carbon transfer paper then painted over.



 Thanks for reading.

29 comments:

  1. Well this is going to be my new project :D Thank you sooooo much for posting these instructions~!

    ReplyDelete
    Replies
    1. your very welcome, I hope to see how it turns out :D

      Delete
  2. I want to buy this.. can i but this product from you?

    ReplyDelete
  3. Legit!! Did you have a template for all the pieces?

    ReplyDelete
  4. Is the Pvc sheeting like Elmer s Foam board?? And where could i buy these sheets??

    ReplyDelete
    Replies
    1. I guess a similiar material you could think it is like is styrene, but a bit thicker.

      If you are unable to find the sheets you could very easyily use the foam core boards, same principle

      Delete
  5. if I could buy one from you, I would be eternally gratefull

    ReplyDelete
    Replies
    1. Unfortunately due to engagements I am unable to fulfil commission requests

      Delete
  6. Im trying to make my own version of this scythe and was wondering if you could make any suggestions for how to make the templates? Thanks and have a great day!

    ReplyDelete
    Replies
    1. This comment has been removed by the author.

      Delete
    2. If you go to this site there is a template of all the parts needed to make the scythe. However i think you will have to work out your own scale. Your also going to have to find out how it all peices together.
      http://www.deviantart.com/art/crescent-rose-all-piece-print-1-1-376836453

      Delete
  7. I LOVE THIS THANK YOU FOR SHARING YOUR WISDOM AND EXPERIENCE. <3

    ReplyDelete
  8. Could you explain what materials are used to make this. I may be creating this. Nice job!

    ReplyDelete
  9. What were your measurements for the blade? I'm making it but don't know how big I need to make it.

    ReplyDelete
  10. can you make me some blueprints that it works like in the anime i'm gonna build it so that it works 100%

    ReplyDelete
    Replies
    1. ho and if you do don't worry about the inside of the gun part or anything and thx for reading

      Delete
  11. I'm trying to make a closed/gun version of Crescent Rose for a Cosplay Convention but i don't know how to make it.can u perhaps teach me how to make it?

    ReplyDelete
  12. This comment has been removed by the author.

    ReplyDelete
  13. what steps you used for each piece sickle? also want to make a

    ReplyDelete
  14. I love the work! I am thinking of making one for my ruby cosplay during aff but sadly, i dont have the tools for making this. But do you recommend styrofoam for this project?

    ReplyDelete
  15. How did you attach the spear point on the bottom of the weapon?

    ReplyDelete
  16. This comment has been removed by the author.

    ReplyDelete
  17. I am in LOVE with Ruby and I hope to be her for Halloween! I am going to make her scythe by myself. I am trying to find some tips and helpful hints on how. Does anyone have an tips or hints for me?

    ReplyDelete
  18. I love this, its awesome. However, I am looking to make a cross over version of rwby and I need to have some kind of in depth template tutorial of the scythe blade. Could there be any chance I could get you to email me the templates u used for your scythe blade please?

    ReplyDelete
  19. OMG thank you soooooo much Im Cosplaying as Ruby so this is perfect

    ReplyDelete
  20. thank you for this step by step I will be using this as a template for the "Crescent Rose" I am making except I will be attempting to build it out of metal and trying to make it work.

    ReplyDelete
  21. I want to cosplay Ruby, but I'm on a tight budget and don't have all the tools you mentioned, so is there any way I could make this with other materials, and if so, what are they?

    ReplyDelete